Godfather Electric Golf Cart Motors
Designed for 48 Volt Club Car Series Carts
New Custom Built Motor, Class H Motor Rating, High Performance Brushes, Torque/Speed Club Car 48 volt Series 10 spline 10.9 HP, Speed 21-23 mph (estimated) and added 20% more torque with stock controller, standard height tires, flat terrain and a good quality battery pack.
Receive a custom stainless steel Plum Quick Xtreme Power ring (size 12 mens only while supplies last) valued at $399.00 free with the purchase of the Godfather Package (motor, controller, wire set, HD Solenoid and HD forward and reverse switch).
Godfather motor: $605.00 + Shipping charges (see shipping chart for cost).
These custom hand built motors usually take 10-20 business days to build from order date. Full credit card payment is required to start the motor build.
*Note: South Carolina residents add 8% for sales tax*
Plum Quick Motors is the World's leader in Golf Cart Performance, we build the most powerful DC Electric motors and we have the World's Fastest Golf Carts to prove it! You need the right components to go with your Custom Built High Performance Motor.
If your cart is equipped with a lift kit and taller tires it is recommended that you upgrade to a Higher amp Controller. We've listed a few different brand controller options below. Add an additional 50% more torque with a 700 amp Series Controller.
*36/48 volt 700 amp Series Controller for your brand golf cart* $625.00
*36/48 volt 600 amp Alltrax SR Series controller for your brand golf cart* $625.00
Complete 2ga. Wire set is required when installing a higher amp controller. *2ga. Wire Set for your brand golf cart* $250.00
*Heavy Duty 36 / 48 volt Solenoid and Diode* are required when installing a higher amp controller. *Heavy Duty 36 / 48 volt Solenoid and Diode* $180.00
Note: Solenoid MUST be mounted upright!
Note: With certain EZ-Go carts (1994-current) you'll need to make sure your ITS is set properly to insure you receive 100% throttle at full pedal.
Note: We like to make sure the plugger rod sticks out around an 1/8" to ensure 100% throttle.
You can't buy a Yamaha Heavy Duty Forward and Reverse Switch. You'll need to make a mounting bracket to use a Heavy Duty Club Car or EZ-GO Forward and Reverse Switch if you have a Yamaha series golf cart. These switches will work for both 36 and 48 volt carts.
You can also use a Heavy Duty Forward and Reverse Contactor. $350
*Heavy Duty Forward and Reverse Switch* is required when installing a higher amp controller.
EZ-GO Heavy Duty Forward and Reverse Switch $180.00.
Club Car Heavy Duty Forward and Reverse Switch. This switch is for 36 / 48 volt golf carts, difference being the number of micro switches. $180.00
To maximize performance replace rear end fluid with high grade synthetic motor oil.
Please note: It is a must that you have a good quality battery pack. At Plum Quick Motors we only use the BEST and in our opinion Trojan batteries are the top of the line.
Always charge your cart after every use and never let your cart sit for over two weeks without charging the cart. Your stock charger will not cut back on after a charge unless you unplug the charger and plug it back up. Make sure your brakes are not dragging, you should be able to push and pull your cart with the brakes released on flat terrain. Also, make sure your tires are properly inflated to 25 - 30 psi.
Note: Installing your custom built motor:
Don’t put a bumper into the motor coupler once you get it back from Plum Quick. The motor has been tested on a dyno machine and if it had a coupler bumper and/or needed a coupler bumper it was tested and determined at that point to use or not. As for installing the motor onto the rear end, wire brush the rear end output spline shaft, you can spray a light coat of white lithium grease and now slide the motor onto the rear spline shaft all the way until the motor housing bumps the rear end housing. Line up and tighten the motor bolts to secure the motor to the rear end housing.
Note: When connecting the motor cables back to the motor it is a MUST that you use two wrenches (one on the nut near the motor housing, so this nut will not turn and the second to tighten the nut that will hold the cable lug) as to not spin the motor stud during the tightening of the cable lug to the motor
Note: Motor rotation:
Once you put in your upgraded motor and it goes in forward with the switch in reverse or goes in reverse when the switch is in forward, simply switch out the S1 and S2 motor leads if it’s a series cart or if it’s a Sepex cart isolate the battery pack and switch out F1 and F2. Test drive the cart and everything should work fine. If you have issues then please give us a call @ 1-803-548-7205.
Note: Motor temperature is very important in the longevity of any motor. Plum Quick motors recommends that the customer monitors the motor temperature with an inexpensive Infrared Temperature Gun. Monitor the temperature on the painted motor case. Motor case temperature of 190 degrees F or lesss is best. Don't operate the cart with motor temperature above 190 degrees F as this can and will break down the winding and armature shellac causing a direct ground. To perform this test you can use a cheap $20 or less Infrared Temperature Gun.
All motors are guaranteed against defects in materials and workmanship for a period of one year from date of purchase from Plum Quick. All motors returned for repairs are subject to manufactures inspection and customer pays for shipping both ways.
Excluded from warranty are motors damaged due to the following. NO exceptions.
1. Stalling the armature (pedal depressed and wheels not turning).
2. Operating the motor under LOW or HIGH voltage conditions (running the motor on LOW battery pack or adding additional voltage to the motor).
3. Exceeding the R.P.M. limit of the motor (running FULL throttle going down steep hills, running motor full throttle with cart on jack stands).
4. Prolonged HIGH amp draw (towing, hauling heavy loads or climbing steep hills or inclines).
5. Using HIGH speed gears (high amp draw).
6. Running OVER 22" tall tires with stock controller (high amp draw).
7. No warranty on speed sensor or magnet for Sepex Motors
Stalling the Armature
Lifted Com bar
Contact Plum Quick
Shipping, handling and replacement insurance rates for golf cart motors shipped within the 48 contiguous states:
Transit Time From:
Steen Products, Inc. / Plum Quick Motors
10590 Tillman Steen Rd.
Fort Mill, SC 29707
Phone: (803) 548-7205
- Zone 1 - $40.00
- Zone 2 - $45.00
- Zone 3 - $50.00
- Zone 4 - $55.00
- Zone 5 - $60.00
Map of estimated transit time* for motors shipped within the 48 contiguous states:
* Published transit times, in business days, are subject to change. Days indicated in color key are business days.
"Over the past two years I have purchased two golf carts from Don Jenkins with the PQ Motor and one with the Center Console w/gear shift; I have been most pleased and recommend to anyone with a cart."— Noel Crick -
The purchaser understands that it is the duty of the purchaser to comply with, and insure compliance with, all necessary safety requirements and agrees to indemnify and hold harmless Plum Quick Motors of any and all liability, direct or indirect, arising from the use or misuse of the merchandise or any other action related to, or incidental to, the merchandise purchased by the purchaser.
The purchaser agrees to allow no individual under the age of majority to operate or otherwise use the merchandise purchased from Plum Quick Motors.
Purchaser agrees to indemnify and hold harmless Plum Quick Motors from any claims of third parties, whether authorized by purchaser or not, arising from, related to, or incidental to this contract or the merchandise purchased pursuant to this contract. Any warranties made by Plum Quick Motors pursuant to this contract may not be transferred to third parties.
Merchandise cannot be disassembled or damaged by incorrect installation. Plum Quick will NOT be liable for any cost of service calls, installation, alleged harm, both personal and materially and/or any damages from the installation of our products. All returns are subject to a 25% restocking fee regardless of reason for return.
Special order custom motors are non-returnable.
If you order a custom motor and receive the wrong motor as a result of misinformation on your part, it cannot be returned.